Lenovo System x3650 M4 HD Installation And Service Manual Download Page 108

Page: 108 / 1168

Step 1.

Read the safety information that begins on page “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Make sure that the server and all peripheral devices are turned off and that the power cords and all
external cables are disconnected.

Step 3.

Reinstall any adapters and reconnect any internal cables that you removed in other procedures.

Step 4.

Align the PCI riser-card assembly with the selected PCI riser-card connector on the system board:

000

000000

0000

000000

000

PCI riser-card
assembly 2

PCI riser-card
assembly 1

Figure 88. PCI riser-card assembly installation

•

PCI riser-card assembly 1

: Carefully fit the two alignment slots on the side of the assembly

onto the two alignment brackets in the side of the chassis.

•

PCI riser-card assembly 2

: Carefully align the bottom edge (the contact edge) of the PCI

riser-card assembly with the PCI riser connector on the system board.

Step 5.

Press down on the assembly. Make sure that the PCI riser-card assembly is fully seated in the PCI
riser connector on the system board.

Replacing the cover

Use this information to reinstall the cover.

To replace the server cover, complete the following steps:

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands