manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 978

User Response

Complete the following steps:

1. If the node has recently been installed, moved, serviced, or upgraded, verify that the DIMM

is properly seated and visually verify that there is no foreign material in any DIMM connector
on that memory channel. If either of these conditions is found, correct and retry with the same
DIMM. (Note: Event Log may contain a recent 00580A4 event denoting detected change in
DIMM population that could be related to this problem.)

2. If no problem is observed on the DIMM connectors or the problem persists, replace the DIMM

identified by LightPath and/or event log entry.

3. If problem re-occurs on the same DIMM connector, replace the other DIMMs on the same

memory channel.

4. Check IBM support site for an applicable service bulletin or firmware update that applies to this

memory error.

5. (Trained Service technician only) If problem re-occurs on the same DIMM connector, inspect

connector for damage. If found, replace system board.

6. (Trained Service technician only) Replace affected Processor.

7. (Trained Service technician only) Replace system board.

•

S.51006 [S.51006] A memory mismatch has been detected. Please verify that the memory

configuration is valid.

Explanation:

One or More Mismatched DIMMs Detected

Severity

Error

User Response

Complete the following steps:

1. Could follow an uncorrectable memory error or failed memory test. Check log and service that

event first. DIMMs disabled by other errors or actions could cause this event.

2. Verify that the DIMMs are installed in the correct population sequence, according to the service

information for this product.

3. Disable memory mirroring and sparing. If this action eliminates the mismatch, check IBM

Support site for information related to this problem.

4.

Reflash UEFI firmware.

5.

Replace DIMM

6. (Trained Service technician only) Replace Processor.

•

S.51009 [S.51009] No system memory has been detected.

Explanation:

No Memory Detected

Severity

Error

User Response

Complete the following steps:

1. Make sure that one or more DIMMs are installed in the server.

966

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands