Lenovo System x3650 M4 HD Installation And Service Manual Download Page 258

Page: 258 / 1168

Pins

Figure 170. Fan bracket installation

Step 5.

Align the holes in the bottom of the bracket with the pins in the bottom of the chassis.

Step 6.

Press the bracket into position until the fan-bracket release levers click into place.

Step 7.

Install the three screws in the fan bracket if present.

Note:

Use the hex screw driver to install the screws.

246

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands