manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 296

Attention:

Do not touch the thermal material on the bottom of the heat sink. Touching the thermal

material will contaminate it. If the thermal material on the microprocessor or heat sink becomes
contaminated, you must wipe off the contaminated thermal material on the microprocessor or heat
sink with the alcohol wipes and reapply clean thermal grease to the heat sink.

a.

Open the heat sink retention module release lever to the fully open position.

b.

Lift the heat sink out of the server. After removal, place the heat sink (with the thermal grease
side up) on a clean, flat surface.

Figure 209. Heat sink removal

Step 7.

Open the microprocessor socket release levers and retainer.

Microprocessor

Microprocessor
release lever

Microprocessor
release lever

Figure 210. Microprocessor socket levers and retainer disengagement

a.

Identify which release lever is labeled as the first release lever to open and open it.

b.

Open the second release lever on the microprocessor socket.

c.

Open the microprocessor retainer.

Attention:

Do not touch the microprocessor contacts. Contaminants on the microprocessor

contacts, such as oil from your skin, can cause connection failures between the contacts
and the socket.

284

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands