Lenovo System x3650 M4 HD Installation And Service Manual Download Page 70

Page: 70 / 1168

• To convert the NIC/iSCSI/FCoE for Emulex Dual Port 10GbE SFP+ Embedded VFA III, complete the

following steps:

1. From the Setup utility main menu (see “Using the Setup utility” on page 103), select

System Settings

➙

Network

and press Enter.

2. From the

Network Device List

, select Emulex network adapter.

Note:

You might need to enter each item (displaying MAC address) to see detailed information.

3. Press Enter to configure Emulex network adapter, select

Personality

and press Enter to change

the settings.

– NIC

– iSCSI (enabled after FoD installed)

– FCoE (enabled after FoD installed)

• To download the latest version of drivers for iSCSI and FCoE from the Lenovo website, complete the

following steps:

1. Go to http://www.ibm.com/support/ fixcentral.

2. Click

Product support

➙

System x

➙

Product family

➙

System x3650 M4 HD

➙

5460

3. From the

Operating system

menu, select your operating system, and then click

Search

to display

the available drivers.

4. Download the latest version of drivers.

– Emulex iSCSI Device Driver for Windows 2008

– Emulex FCoE Device Driver for Windows 2008

Note:

Changes are made periodically to the Lenovo website. The actual procedure might vary slightly

from what is described in this document.

• Port 0 on the Emulex Dual Port 10GbE SFP+ Embedded VFA III can be configured as shared system

management.

• When the server is in standby mode, both ports on the Emulex Dual Port 10GbE SFP+ Embedded VFA

III function at 100M connection speed with Wake on LAN feature.

The Emulex Dual Port 10GbE SFP+ Embedded VFA III is automatically disabled if one of the following
errors occurs:

• An error log indicates a temperature warning for the Ethernet adapter.

• All power supplies are removed or the server is disconnected from the power source.

To install the dual-port network adapter, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

Remove the cover (see “Removing the cover” on page 37).

Step 4.

Remove PCI riser-card assembly 2, if any (see “Removing a PCI riser-card assembly” on page 221).

Step 5.

Loosen the thumbscrew to remove the network adapter filler panel on the rear of the chassis (if
it has not been removed already).

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands