manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 302

Figure 217. Heat-sink lever rotation

Step 6.

Open the microprocessor socket release levers and retainer:

Figure 218. Microprocessor socket levers and retainer disengagement

a.

Identify which release lever is labeled as the first release lever to open and open it.

b.

Open the second release lever on the microprocessor socket.

c.

Open the microprocessor retainer.

Attention:

Do not touch the connectors on the microprocessor and the microprocessor socket.

Step 7.

Install the microprocessor in the microprocessor socket:

a.

Open the packaging that contains the new microprocessor installation tool assembly and
carefully remove the installation tool assembly from the package.

Note:

Do not touch the microprocessor contacts. Contaminants on the microprocessor

contacts, such as oil from your skin, can cause connection failures between the contacts
and the socket.

b.

Remove the microprocessor protective cover if one is present. The microprocessor is
preinstalled on the installation tool.

290

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands