Lenovo System x3650 M4 HD Installation And Service Manual Download Page 1122

Page: 1122 / 1168

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Insert a new CD or DVD into the drive and wait for 15 seconds for the media to be recognized.

Rerun the test.

2. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-803-000 : Optical Drive Test Failed

Optical Drive Test Failed. Disk may be in use by the operating system.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Wait for the system activity to cease

2. Run the test again

3. Turn off and restart the system.

4. Run the test again.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

1110

Lenovo System x3650 M4 HD Installation and Service Guide

«
...
1120
1121
1122
1123
1124
...
»

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands