Lenovo System x3650 M4 HD Installation And Service Manual Download Page 1125

Page: 1125 / 1168

User Response

Complete the following steps:

1. Insert a new CD or DVD into the drive and wait for 15 seconds for the media to be recognized.

Rerun the test.

2. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

3. Run the test again.

4. Check system firmware level and upgrade if necessary.The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

5. Run the test again.

6. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA system management test results

The following messages can result when you run the system management test.

Test results for the DSA system management test

The following messages can result when you run the DSA system management test.

•

166-000-001 : IMM I2C Test Passed

IMM I2C Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-801-001 : IMM I2C Test Aborted

Appendix C. DSA diagnostic test results

1113

«
...
1123
1124
1125
1126
1127
...
»

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands