manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 431

50

CIM Information

Prefix:

PLAT

ID:

0522

User Response

None

•

8007020c-2508ffff : Sensor [SensorElementName] has transitioned to critical from a less severe

state. (nvDIMM 08 Status)

This message is for the use case when an implementation has detected a Sensor transitioned to critical
from less severe.

May also be shown as 8007020c2508ffff or 0x8007020c2508ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Other

SNMP Trap ID

50

CIM Information

Prefix:

PLAT

ID:

0522

User Response

None

•

8007020c-250bffff : Sensor [SensorElementName] has transitioned to critical from a less severe

state. (nvDIMM 11 Status)

This message is for the use case when an implementation has detected a Sensor transitioned to critical
from less severe.

May also be shown as 8007020c250bffff or 0x8007020c250bffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Other

Appendix A. Integrated management module II (IMM2) error messages

419

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands