manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 109

Step 1.

Make sure that all cables, adapters, and other components are installed and seated correctly
and that you have not left loose tools or parts inside the server. Also, make sure that all internal
cables are correctly routed.

Before you slide the cover forward, make sure that all the tabs on the front, rear, and side of the
cover engage the chassis correctly. If all the tabs do not engage the chassis correctly, it will be
very difficult to remove the cover later.

Step 2.

Position the cover on top of the server.

Step 3.

Slide the cover toward the front of the server.

Step 4.

Make sure that the cover correctly engages all the inset tabs on the server.

Step 5.

Press down the blue latch on the top (in the center of the front of the server) of the cover.

0

0

0

0

0

0

0

000000000000

000000000000

000000000000

000000000000

000000000000

000000000000

000000000000

Cover-release
latch

1

2

Figure 89. Cover installation

Step 6.

Slide the server all the way into the rack until it latches.

Connecting the external cables

The following illustrations show the locations of the input and output connectors of the server.

The following illustrations show the locations of the input and output connectors on the front and rear of
the server.

Video and USB
breakout connector

Figure 90. Front view

Chapter 2

.

Installing optional devices

97

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands