Lenovo System x3650 M4 HD Installation And Service Manual Download Page 716

Page: 716 / 1168

CIM Information

Prefix:

PLAT

ID:

0481

User Response

If the specified sensor is one of the following, SysBrd 3.3V, SysBrd 5V or SysBrd 12V: No action;
information only.

•

81010204-1d01ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 1A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102041d01ffff or 0x810102041d01ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

User Response

No action; information only. Fan 1B Tach :

•

81010204-1d02ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 2A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102041d02ffff or 0x810102041d02ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

704

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands