manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 405

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Temperature

SNMP Trap ID

0

CIM Information

Prefix:

PLAT

ID:

0494

User Response

1. Make sure the air baffles/heat sink are placed and correctly installed; and make sure the node

cover is installed and completely closed.

2. Make sure the fans are operating, and there are no obstructions to the airflow.

3. Reduce the Ambient temperature. The system must be operating within the specifications.(see

Features and specifications for more information)

•

80010901-0c01ffff : Numeric sensor [NumericSensorElementName] going high (upper critical) has

asserted. (Ambient Temp)

This message is for the use case when an implementation has detected an Upper Critical sensor going
high has asserted.

May also be shown as 800109010c01ffff or 0x800109010c01ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Temperature

SNMP Trap ID

0

CIM Information

Prefix:

PLAT

ID:

0494

User Response

Appendix A. Integrated management module II (IMM2) error messages

393

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands