manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 143

System error
LED

Locator LED

Power LED

Dual-por t network
adapter LED

IMM hear tbeat
LED

RTMM hear tbeat LED

Standby power
LED

System battery
error LED

Fan 4
error LED

Fan 3
error LED

Microprocessor 2
error LED

Fan 2
error LED

Fan 1
error LED

Microprocessor 1
error LED

System board
error LED

DIMM 19-24
error LEDs
(under the latches)

DIMM 1-6
error LEDs
(under the latches)

DIMM 7-18
error LEDs
(under the latches)

Figure 94. System board error LEDs

Power-supply LEDs

The following minimum configuration is required for the server to start.
• One microprocessor in microprocessor socket 1
• One 2 GB DIMM on the system board
• One power supply
• Power cord
• Four cooling fans
• One PCI riser-card assembly in PCI connector 1

AC power-supply LEDs

Use this information to view AC power-supply LEDs.

The following minimum configuration is required for the DC LED on the power supply to be lit:
• Power supply
• Power cord

Note:

You must turn on the server for the DC LED on the power supply to be lit.

The following illustration shows the locations of the power-supply LEDs on the ac power supply.

Chapter 4

.

Troubleshooting

131

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands