Lenovo System x3650 M4 HD Installation And Service Manual Download Page 800

Page: 800 / 1168

CIM Information

Prefix:

PLAT

ID:

0167

User Response

No action; information only.

•

816f010d-040affff : The Drive [StorageVolumeElementName] has been enabled. (Drive 10)

This message is for the use case when an implementation has detected a Drive was Enabled.

May also be shown as 816f010d040affff or 0x816f010d040affff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0167

User Response

No action; information only.

•

816f010d-040bffff : The Drive [StorageVolumeElementName] has been enabled. (Drive 11)

This message is for the use case when an implementation has detected a Drive was Enabled.

May also be shown as 816f010d040bffff or 0x816f010d040bffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0167

788

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands