Lenovo System x3650 M4 HD Installation And Service Manual Download Page 1121

Page: 1121 / 1168

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-801-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. Unable to communicate with driver.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Make sure that the DSA Diagnostic code is at the latest level.

2. Run the test again.

3. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

4. Run the test again.

5. Check system firmware level and upgrade if necessary.The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

6. Run the test again.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-802-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. A read error was encountered.

Recoverable

Appendix C. DSA diagnostic test results

1109

«
...
1119
1120
1121
1122
1123
...
»

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands