Lenovo System x3650 M4 HD Installation And Service Manual Download Page 743

Page: 743 / 1168

•

81070204-0a01ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (PS 1 Fan Fault)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 810702040a01ffff or 0x810702040a01ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only.

•

81070204-0a02ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (PS 2 Fan Fault)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 810702040a02ffff or 0x810702040a02ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only.

Appendix A. Integrated management module II (IMM2) error messages

731

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands