manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 521

•

806f011b-2502ffff : The connector [PhysicalConnectorElementName] has encountered a

configuration error. (nvDIMM 02 Cable)

This message is for the use case when an implementation has detected an Interconnect Configuration
Error.

May also be shown as 806f011b2502ffff or 0x806f011b2502ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Other

SNMP Trap ID

50

CIM Information

Prefix:

PLAT

ID:

0266

User Response

If the specified sensor is front USB connector, reset the front USB cable on the system board. If
the specified sensor is front video connector, reset the front video cable in the system board. If the
specified sensor is PwrPaddle cable, complete the following steps until problem is solved:

1. Reseat the power paddle cable on the system board.

2. Replace the power paddle cable.

3. (Trained technician only) Replace the supercap n. (n = supercap number)

4. (Trained technician only) Replace the system board.

•

806f011b-2505ffff : The connector [PhysicalConnectorElementName] has encountered a

configuration error. (nvDIMM 05 Cable)

This message is for the use case when an implementation has detected an Interconnect Configuration
Error.

May also be shown as 806f011b2505ffff or 0x806f011b2505ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Other

Appendix A. Integrated management module II (IMM2) error messages

509

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands