manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 248

To remove the dual-port network adapter, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

Remove the cover (see “Removing the cover” on page 195).

Step 4.

Remove PCI riser-card assembly 2, if any (see “Removing a PCI riser-card assembly” on page 221).

Step 5.

Loosen the two captive screws on the network adapter from the screw holes on the system board.

00

00

00

00

00

0

0

00

000

000

000

000

000

Pin

Thumbscrew

Retention
brackets

Captive screws

Figure 161. Screws disengagement

Step 6.

Loosen the thumbscrew on the chassis.

Step 7.

Grasp the network adapter and disengage it from the pin, retention brackets, and the connector on
the system board; then, lift the adapter out of the port openings on the rear of the chassis and
remove it from the server.

236

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands