Lenovo System x3650 M4 HD Installation And Service Manual Download Page 20 | Manualshive

Page: 20 / 1168

Lenovo System x3650 M4 HD Installation And Service Manual Download Page 20

Power supply:

• Up to two hot-swap power supplies for redundancy support

– 550-watt ac

– 750-watt ac

– 750-watt dc

– 900-watt ac

Notes:

• Power supplies in the server must be with the same power rating or wattage.

Hot-swap fans:

The server supports 4 hot-swap fans.

RAID controllers (depending on the model):

Supported on-board RAID controllers:

• ServeRAID M5210e

Integrated functions:

• Integrated Management Module II (IMM2), which consolidates multiple management functions in a

single chip.

• Intel I350AM4 Quad Port Gigabit Ethernet controller with Wake on LAN support
• Universal Serial Bus (USB) ports

– Front (optional): two ports (supported when the video and USB breakout cable is installed)
– Rear: four ports
– Internal: one port for Hypervisor USB key

• Six network ports (four 1 Gb Ethernet ports on the system board and two additional ports when the

optional dual-port network adapter is installed)

• One System Management RJ-45 on the rear to connect to a systems management network. This

system management connector is dedicated to the IMM2 functions.

• One serial port
• Two VGA ports. One is on the rear, the other one is optional when the video and USB breakout

cable is installed

• Light path diagnostics panel

Video controller (integrated into the IMM2):

• Matrox G200eR core (two analog ports: one front and one rear that can be connected at the same

time)

Note:

The maximum video resolution is 1600 x 1200 at 75 Hz.

– SVGA compatible video controller
– DDR3 528 MHz SDRAM video memory controller
–

Avocent Digital Video Compression

– 16 MB of video memory (not expandable)

Size (2U):

• Height: 86.5 mm (3.406 in.)
• Depth: EIA flange to rear - 714 mm (28.110 in.), Overall - 746 mm (29.370 in.)
• Width: With top cover - 445 mm (17.520 in.), With front bezel - 482.0 mm (18.976 in.)
• Weight: approximately 25 kg (55 lb) to 30 kg (65 lb) depending upon configuration

Acoustical noise emissions:

• Sound power, idling: 6.3 bels maximum
• Sound power, operating: 7.0 bels maximum

8

Lenovo System x3650 M4 HD Installation and Service Guide

«
...
18
19
20
21
22
...
»

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands