Lenovo System x3650 M4 HD Installation And Service Manual Download Page 65

Page: 65 / 1168

Installing the ServeRAID adapter memory module

Use this information to install the ServeRAID adapter memory module.

To install the ServeRAID adapter memory module, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 37).

Step 4.

Connect the cable to the ServeRAID adapter memory module.

ServeRAID memory module

Flash power module cable

Figure 38. Cable installation

Step 5.

Align the memory module with the retention pins. Install the memory module into the system board.

Connector

Rentention pins

ServeRAID memory module

Figure 39. ServeRAID adapter memory module installation

Step 6.

Connect the other end of the cable to the flash power module.

Chapter 2

Installing optional devices

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands