manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 277

00

00

00

00

00

0

0

00

000

000

000

000

000

USB embedded
hypervisor
flash device

Lockbar

Figure 186. USB hypervisor flash device removal

a.

Unlock the retention latch on the USB connector by pushing down on the blue lockbar.

b.

Grasp the flash device and pull to remove it from the connector.

If you are instructed to return the flash device, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.

Replacing a USB embedded hypervisor flash device

Use this information to replace a USB embedded hypervisor flash device.

To install a USB hypervisor flash device, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 195).

Step 4.

Remove PCI riser-card assembly 2 (see “Removing a PCI riser-card assembly” on page 221).

Step 5.

Install the flash device:

Chapter 6

.

Removing and replacing components

265

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands