manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 191

Chapter 6. Removing and replacing components

There are three types of replaceable components.

•

Structural parts:

Purchase and replacement of structural parts (components, such as chassis assembly,

top cover, and bezel) is your responsibility. If Lenovo acquires or installs a structural component at
your request, you will be charged for the service.

•

Tier 1 customer replaceable unit (CRU):

Replacement of Tier 1 CRUs is your responsibility. If Lenovo

installs a Tier 1 CRU at your request, you will be charged for the installation.

•

Tier 2 customer replaceable unit:

You may install a Tier 2 CRU yourself or request Lenovo to install it, at

no additional charge, under the type of warranty service that is designated for your server.

See Chapter 5 “Parts listing, Lenovo System x3650 M4 HD Type 5460” on page 167 to determine whether a
component is a structural part, Tier 1 CRU, or Tier 2 CRU.

For information about the terms of the warranty, see the

Warranty Information

document that comes with

the server.

For more information about getting service and assistance, see Appendix D “Getting help and technical
assistance” on page 1135.

Returning a device or component

If you are instructed to return a device or component, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Internal cable routing and connectors

This section provides information about routing the cables when you install some components in the server.

For more information about the requirements for cables and connecting devices, see the documentation
that comes with these devices.

Cabling front USB and video connector

The internal routing and connector for the front USB and video cable.

The following illustration shows the internal routing and connectors for the front USB and video cable.

© Copyright Lenovo 2015, 2016

179

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands