Lenovo System x3650 M4 HD Installation And Service Manual Download Page 194

Page: 194 / 1168

00000000

000000

Video graphic
adapters

Video graphic adapter
power connector for riser 2

Video graphic
adapter power
cables

Video graphic adapter
power connector for riser 1

Figure 103. Video graphic adapter cables connection

Cabling backplane

The internal routing and connectors for the backplanes.

Attention:

Please note that the mini-SAS cables for some systems do not connect to the system board but

to the RAID adapters.

16x2.5-inch drive model

The internal routing and connectors for the 16x2.5-inch drive model cables.

The following illustration shows the internal routing and connectors for the 16x2.5-inch hot-swap HDD model.

182

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands