manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 110

0

000

000

000

000

00

000

000

000

000

000

00

00

00

00

000

000

000

000

000

000

0000000

0000000

0000000

0000000

Video Serial

Power supply 1

Power supply 2

Shared system
management

Dedicated system
management

Network connectors
(with optional adapter)

USB
connectors

Ethernet
connectors

Drive bay 24

Drive bay 25

Figure 91. Rear view

You must turn off the server before you connect or disconnect cables.

See the documentation that comes with any external devices for additional cabling instructions. It might be
easier for you to route cables before you connect the devices to the server.

If the server comes with an installed operating system, see the documentation that comes with the operating
system for additional cabling instructions.

Updating the server configuration

When you start the server for the first time after you add or remove a device, you might receive a message
that the configuration has changed. The Setup utility starts automatically so that you can save the new
configuration settings.

Some optional devices have device drivers that you must install. For information about installing device
drivers, see the documentation that comes with each device.

If the server has an optional RAID adapter and you have installed or removed a hard disk drive, see the
documentation that comes with the RAID adapter for information about reconfiguring the disk arrays.

For information about configuring the integrated Gigabit Ethernet controller, see “Configuring the Ethernet
controller” on page 114.

98

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands