Lenovo System x3650 M4 HD Installation And Service Manual Download Page 41

Page: 41 / 1168

System
management
(dedicated)

Video
connector

Serial
connector

USB connectors

Ethernet connector
System management (shared)

Ethernet connectors

Figure 15. System-board external connectors

System-board switches, jumpers, and buttons

The following illustration shows the location of the switches, jumpers, and buttons on the server.

Important:

1. Before you change any switch settings or move any jumpers, turn off the server; then, disconnect all

power cords and external cables. Review the information in “Safety” on page v, “Installation guidelines”
on page 34, “Handling static-sensitive devices” on page 36, and “Turning off the server” on page 23.

2. Any system-board switch or jumper block that is not shown in the illustrations in this document are

reserved.

3. If there is a clear protective sticker on the top of the switch blocks, you must remove and discard it to

access the switches.

Chapter 2

Installing optional devices

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands