manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 341

CIM Information

Prefix:

IMM

ID:

0032

User Response

Information only; no action is required.

•

40000021-00000000 : Management Controller [arg1] clock has been set from NTP server [arg2].

This message is for the use case where a Management Controller clock has been set from the Network
Time Protocol server.

May also be shown as 4000002100000000 or 0x4000002100000000

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0033

User Response

Information only; no action is required.

•

40000022-00000000 : SSL data in the Management Controller [arg1] configuruation data is invalid.

Clearing configuration data region and disabling SSL.

This message is for the use case where a Management Controller has detected invalid SSL data in the
configuration data and is clearing the configuration data region and disabling the SSL.

May also be shown as 4000002200000000 or 0x4000002200000000

Severity

Error

Serviceable

No

Automatically notify support

No

Alert Category

System - other

SNMP Trap ID

Appendix A. Integrated management module II (IMM2) error messages

329

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands