manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 45

Microprocessor 1

Microprocessor 2

PCI riser connector 1

PCI riser connector 2

Dual-por t network
adapter connector

DIMMs 1-6

DIMMs 19-24

DIMMs 7-18

Figure 18. System-board optional-device connectors

PCI riser-card adapter connectors

The following illustration shows the connectors on the PCI riser card for user-installable PCI adapters.

00

00000

00000

00000

000000

000000

000000

000000

00000

00000

00000

0000000

0000000

0000000

0000000

0000000

00

0

PCI riser-card assembly
(in long position)

Adapter

Adapter
connectors

PCI riser-card assembly
(in short position)

Adapter

Adapter
connectors

Full-length
adapter
bracket

Full-length
adapter
bracket

Figure 19. PCI riser-card adapter connectors

Chapter 2

.

Installing optional devices

33

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands