Lenovo System x3650 M4 HD Installation And Service Manual Download Page 253

Page: 253 / 1168

000

Thumbscrew

Retention
brackets

Captive screws

Figure 165. Screws engagement

Step 10. Fasten the two captive screws on the network adapter.

Step 11. Reinstall PCI riser-card assembly 2 in PCI riser connector 2 if you have removed it previously (see

“Replacing a PCI riser-card assembly” on page 222).

Step 12. Replace the cover (see “Replacing the cover” on page 196).

Step 13. Slide the server into the rack.

Step 14. Reconnect the power cords and any cables that you removed.

Step 15. Turn on the peripheral devices and the server.

Removing a hot-swap fan

Use this information to remove a hot-swap fan.

Attention:

To ensure proper server operation, replace a failed hot-swap fan within 30 seconds.

To remove a hot-swap-fan, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Remove the cover (see “Removing the cover” on page 195). The LED on the system board near the
connector for the failing hot-swap fan will be lit.

Attention:

To ensure proper system cooling, do not remove the top cover for more than 30 minutes

during this procedure.

Step 3.

Grasp the hot-swap fan by the finger grips on the sides of the dual-motor hot-swap fan.

Chapter 6

Removing and replacing components

241

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands