manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 207

Backplane
connection
cable

Power
cable

Configuration
cable

Backplane

Power
cable

Configuration
cable

Expander

Mini-SAS cable

Power
cable

Power
cable

Mini-SAS cable

Mini-SAS cable

1.8-inch backplane assembly

1.8-inch backplane assembly

Configuration
cable

Configuration
cable

Figure 116. 16x2.5-inch and 16x1.8-inch drive model cable connection

Removing and replacing server components

This section provides information for removing and replacing components in the server.

Removing and replacing structural parts

Replacement of structural parts is your responsibility. If Lenovo installs a structural part at your request,
you will be charged for the installation.

The illustrations in this document might differ slightly from your hardware.

Removing the cover

Use this information to remove the cover.

To remove the server cover, complete the following steps:

Step 1.

Read the safety information that begins on page “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

If the server has been installed in a rack, slide the server out from the rack enclosure.

Chapter 6

.

Removing and replacing components

195

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands