manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 972

3. If error persists, or boot is unsuccessful, (Trained service technician only) Replace the system

board.

•

I.3818003 [I.3818003] The CRTM flash driver could not lock the secure flash region.

Explanation:

CRTM Could not lock secure flash region

Severity

Info

User Response

Complete the following steps:

1. If system failed to boot successfully, DC cycle system.

2. If system boots to F1 setup, flash UEFI image and reset bank to primary (if required). If system

boots without error, recovery is complete and no additional action is required.

3. If system fails to boot, or if flash attempt fails, (Trained service technician only) Replace the

system board.

•

I.58015 [I.58015] Memory spare copy initiated.

Explanation:

Spare Copy Started

Severity

Info

User Response

Complete the following steps:

1. No user required for this event. This is for informational purposes only.

•

I.580A4 [I.580A4] Memory population change detected.

Explanation:

DIMM Population Change Detected

Severity

Info

User Response

Complete the following steps:

1. Check system event log for uncorrected DIMM failures and replace those DIMMs.

•

I.580A5 [I.580A5] Mirror Fail-over complete. DIMM number % has failed over to to the mirrored

copy.

Explanation:

DIMM Mirror Fail-over Detected

Severity

Info

User Response

Complete the following steps:

1. Check the system-event log for uncorrected DIMM failures and replace those DIMMs.

960

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands