manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 332

No

Automatically notify support

No

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0015

User Response

Information only; no action is required.

•

40000010-00000000 : Security: Userid: [arg1] had [arg2] login failures from WEB client at IP

address [arg3].

This message is for the use case where a user has failed to log in to a Management Controller from
a web browser.

May also be shown as 4000001000000000 or 0x4000001000000000

Severity

Warning

Serviceable

No

Automatically notify support

No

Alert Category

System - Remote Login

SNMP Trap ID

30

CIM Information

Prefix:

IMM

ID:

0016

User Response

Complete the following steps until the problem is solved:

1. Make sure that the correct login ID and password are being used.

2. Have the system administrator reset the login ID or password.

•

40000011-00000000 : Security: Login ID: [arg1] had [arg2] login failures from CLI at [arg3].

This message is for the use case where a user has failed to log in to a Management Controller from
the Legacy CLI.

May also be shown as 4000001100000000 or 0x4000001100000000

320

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands