manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 217

Battery 2 / flash power module 2

Battery 1 / flash power module 1

Figure 126. RAID adapter battery or flash power module installation

Note:

The positioning of the battery or flash power module depends on the type of the

batteries or flash power modules that you install.

b.

Connect the other end of the cable to the battery or flash power module.

00000

00000

00000

00000

00000

00000

Flash power module cable

ServeRAID memory module

Flash power module

Figure 127. Battery or flash power module cable installation

Note:

Make sure the battery or flash power module is seated properly.

Chapter 6

.

Removing and replacing components

205

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands