manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 629

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - CPU

SNMP Trap ID

40

CIM Information

Prefix:

PLAT

ID:

0816

User Response

1. Make sure that the installed microprocessors are compatible with each other (see Installing a

microprocessor and heat sink for information about microprocessor requirements).

2. Update the server firmware to the latest level (see Updating the firmware).

3. (Trained technician only) Replace the incompatible microprocessor.

•

806f0607-0302ffff : An SM BIOS Uncorrectable CPU complex error for [ProcessorElementName]

has asserted. (CPU 2)

This message is for the use case when an SM BIOS Uncorrectable CPU complex error has asserted.

May also be shown as 806f06070302ffff or 0x806f06070302ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - CPU

SNMP Trap ID

40

CIM Information

Prefix:

PLAT

ID:

0816

User Response

1. Make sure that the installed microprocessors are compatible with each other (see Installing a

microprocessor and heat sink for information about microprocessor requirements).

2. Update the server firmware to the latest level (see Updating the firmware).

3. (Trained technician only) Replace the incompatible microprocessor.

Appendix A. Integrated management module II (IMM2) error messages

617

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands