manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 467

3. (Trained technician only) Replace the system board.

Firmware Error : Sys Boot Status :

•

806f000f-220103ff : The System [ComputerSystemElementName] encountered firmware error -

unrecoverable boot device failure. (ABR Status)

This message is for the use case when an implementation has detected that System Firmware Error
Unrecoverable boot device failure has occurred.

May also be shown as 806f000f220103ff or 0x806f000f220103ff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0770

User Response

This is a UEFI detected event. The UEFI(POST) error code for this event can be found in the logged
IMM message text. Please refer to the UEFI(POST) error code in the "UEFI(POST) error code" section
of the Information Center for the appropriate user response. Firmware Error : Sys Boot Status :

•

806f000f-220104ff : The System [ComputerSystemElementName]has encountered a motherboard

failure. (ABR Status)

This message is for the use case when an implementation has detected that a fatal motherboard failure in
the system.

May also be shown as 806f000f220104ff or 0x806f000f220104ff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Other

SNMP Trap ID

Appendix A. Integrated management module II (IMM2) error messages

455

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands