Lenovo System x3650 M4 HD Installation And Service Manual Download Page 1021

Page: 1021 / 1168

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

217-900-000 : HDD Test Failed

HDD Test Failed. The hard drive self-test detected a failure.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check cable connections.

2. Rerun the test.

3. Verify the firmware is at the latest level.

4. Rerun the test.

5. If the problem remains, contact your technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Intel network test results

The following messages can result when you run the Intel network test.

Test results for the DSA Intel network test

The following messages can result when you run the DSA Intel network test.

•

406-000-000 : IANet:Registers Test Passed

The test passed.

Recoverable

Severity

Event

Appendix C. DSA diagnostic test results

1009

«
...
1019
1020
1021
1022
1023
...
»

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands