Lenovo System x3650 M4 HD Installation And Service Manual Download Page 423

Page: 423 / 1168

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0508

User Response

1. Replace the power supply with higher rated power.

2. Reduce the total power consumption by removing newly added or unused option like drives or

adapters.

•

80070101-0c01ffff : Sensor [SensorElementName] has transitioned from normal to non-critical

state. (Ambient Status)

This message is for the use case when an implementation has detected a Sensor transitioned to
non-critical from normal.

May also be shown as 800701010c01ffff or 0x800701010c01ffff

Severity

Warning

Serviceable

Yes

Automatically notify support

Alert Category

Warning - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0520

User Response

1. Check the microprocessor installed is Intel E5-2690.

2. Reduce the ambient temperature under 27 Celsius degree.

•

8007010f-2201ffff : Sensor [SensorElementName] has transitioned from normal to non-critical

state. (GPT Status)

This message is for the use case when an implementation has detected a Sensor transitioned to
non-critical from normal.

May also be shown as 8007010f2201ffff or 0x8007010f2201ffff

Appendix A. Integrated management module II (IMM2) error messages

411

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands