manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 1009

Recoverable

No

Severity

Event

Serviceable

No

Automatically notify support

No

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

180-801-000 : Check-point Panel Test Aborted

Check-point Panel Test Aborted. BMC is unable to verify that the operator information panel cable is
connected.

Recoverable

No

Severity

Warning

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Inspect and reseat operator information panel cable at both ends.

2. Verify that the Baseboard Management Controller (BMC) is working.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

180-901-000 : Check-point Panel Test Failed

Check-point Panel Test Failed. Operator reported incorrect display.

Recoverable

No

Severity

Appendix C. DSA diagnostic test results

997

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands