Lenovo System x3650 M4 HD Installation And Service Manual Download Page 779

Page: 779 / 1168

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0331

User Response

No action; information only. One of PCI Error :

•

816f0021-2c01ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName]. (Mezz Error)

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed.

May also be shown as 816f00212c01ffff or 0x816f00212c01ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0331

User Response

No action; information only.

•

816f0021-3001ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName]. (PCI 1)

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed.

May also be shown as 816f00213001ffff or 0x816f00213001ffff

Severity

Info

Appendix A. Integrated management module II (IMM2) error messages

767

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands