manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 72

00

00

00

00

00

0

0

00

000

000

000

000

000

Pin

Thumbscrew

Screw holes

Retention
brackets

Network
adapter

Captive screws

Network
adapter connector

Figure 46. Network adapter installation

Step 8.

Press the adapter firmly until the pin, and retention brackets engage the adapter. Make sure the
adapter is securely seated on the connector on the system board.

Attention:

Make sure the port connectors on the adapter are aligned properly with the chassis on

the rear of the server. An incorrectly seated adapter might cause damage to the system board
or the adapter.

Step 9.

Fasten the thumbscrew on the rear side of the chassis.

60

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands