manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 44

System error
LED

Locator LED

Power LED

Dual-por t network
adapter LED

IMM hear tbeat
LED

RTMM hear tbeat LED

Standby power
LED

System battery
error LED

Fan 4
error LED

Fan 3
error LED

Microprocessor 2
error LED

Fan 2
error LED

Fan 1
error LED

Microprocessor 1
error LED

System board
error LED

DIMM 19-24
error LEDs
(under the latches)

DIMM 1-6
error LEDs
(under the latches)

DIMM 7-18
error LEDs
(under the latches)

Figure 17. System-board LEDs

System-board optional-device connectors

The following illustration shows the connectors on the system board for the optional devices.

32

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands