Lenovo System x3650 M4 HD Installation And Service Manual Download Page 236

Page: 236 / 1168

000

000000

0000

000000

000

PCI riser-card
assembly 2

PCI riser-card
assembly 1

Figure 146. PCI riser-card assembly installation

PCI connector 2

: Carefully align the bottom edge (the contact edge) of the riser-card

assembly with the riser-card connector on the system board.

Step 6.

Press down on the assembly. Make sure that the riser-card assembly is fully seated in the
riser-card connector on the system board.

Step 7.

Replace the cover (see “Replacing the cover” on page 196).

Step 8.

Slide the server into the rack.

Step 9.

Reconnect the power cords and any cables that you removed.

Step 10. Turn on the peripheral devices and the server.

Removing the rear two hard-disk-drive kit

The server comes with one rear two hard-disk-drive kit.

See http://www.lenovo.com/ serverproven/ for a list of hard disk drives that you can use with the server.

To remove the rear two hard-disk-drive kit, complete the following steps:

Step 1.

Read the safety information that begins on page “Safety” on page v and “Installation guidelines”
on page 34.

224

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands

Lenovo System x3650 M4 HD, Installation And Service Manual

Search results

Summary of Contents for System x3650 M4 HD

Reviews:

Brands by name

Popular brands