Intel 80C186XL User Manual Download Page 308 | Manualshive

Page: 308 / 405

background image

A-1

APPENDIX A

80C186 INSTRUCTION SET

ADDITIONS AND EXTENSIONS

The 80C186 Modular Core family instruction set differs from the original 8086/8088 instruction
set in two ways. First, several instructions that were not available in the 8086/8088 instruction set
have been added. Second, several 8086/8088 instructions have been enhanced for the 80C186
Modular Core family instruction set.

A.1

80C186 INSTRUCTION SET ADDITIONS

This section describes the seven instructions that were added to the base 8086/8088 instruction
set to make the instruction set for the 80C186 Modular Core family. These instructions did not
exist in the 8086/8088 instruction set.

•

Data transfer instructions

— PUSHA

— POPA

•

String instructions

— INS

— OUTS

•

High-level instructions

— ENTER

— LEAVE

— BOUND

A.1.1

Data Transfer Instructions

PUSHA/POPA

PUSHA (push all) and POPA (pop all) allow all general-purpose registers to be stacked and un-
stacked. The PUSHA instruction pushes all CPU registers (except as noted below) onto the stack.
The POPA instruction pops all registers pushed by PUSHA off of the stack. The registers are
pushed onto the stack in the following order: AX, CX, DX, BX, SP, BP, SI, DI. The Stack Pointer
(SP) value pushed is the Stack Pointer value before the AX register was pushed. When POPA is
executed, the Stack Pointer value is popped, but ignored. Note that this instruction does not save
segment registers (CS, DS, SS, ES), the Instruction Pointer (IP), the Processor Status Word or
any integrated peripheral registers.

«
...
306
307
308
309
310
...
»

Summary of Contents for 80C186XL






















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 80C186XL

Brand: 3Com Pages: 8

Brand: XESS Pages: 23

UniFi Cloud Key

Brand: Ubiquiti Pages: 13

Brand: VideoWave Pages: 12

Brand: Ciara Pages: 14

Brand: Camozzi Pages: 22

Brand: Aaeon Pages: 100

X570 AORUS ELITE WIFI

Brand: Gigabyte Pages: 48

Brand: LevelOne Pages: 10

Brand: SET Pages: 38

ForeFront 2616RC

Brand: Patton electronics Pages: 80

Brand: GE Pages: 24

IS200ADIIH A Series

Brand: GE Pages: 20

VersaMax IC754TAN001

Brand: GE Pages: 17

Brand: GE Pages: 30

VMIVME-2533 Series

Brand: GE Pages: 38

Brand: GE Pages: 38

QuickPanel+ IC754VSB06CTD

Brand: GE Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands