manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Port Trunking    

Port Status and Configuration 

LACP trunk status commands include: 

Trunk Display Method 

Static LACP Trunk 

Dynamic LACP Trunk 

CLI 

show lacp

 command 

Included in listing. 

Included in listing. 

CLI 

show trunk 

command 

Included in listing. 

Not included. 

Port/Trunk Settings screen in menu interface 

Included in listing. 

Not included 

Thus, to display a listing of dynamic LACP trunk ports, you must use the 

show 

lacp

 command. 

N o t e    

Dynamic LACP trunks operate only in the default VLAN (unless GVRP is 
enabled and 

Forbid

 is used to prevent the trunked ports from joining the default 

VLAN). Thus, if an LACP dynamic trunk forms using ports that are not in the 
default VLAN, the trunk will automatically move to the default VLAN unless 
GVRP operation is configured to prevent this from occurring. In some cases, 
this can create a traffic loop in your network. For more on this topic, refer to 
“VLANs and Dynamic LACP” on page 12-20. 

In most cases, trunks configured for LACP operate as described in table 12-4 
on the next page. 

12-16 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link DAP-1650 Quick Install Manual preview
DAP-1650
Brand: D-Link Pages: 16
D-Link DCH-G020 How-To preview
DCH-G020
Brand: D-Link Pages: 2
KELCO E30 Installation & Programming Manual preview
E30
Brand: KELCO Pages: 41
United Electric Controls 54 Series Assembly, Installation And Operation Instructions preview
54 Series
Brand: United Electric Controls Pages: 6
Quintum Tenor AXE1600 Specifications preview
Tenor AXE1600
Brand: Quintum Pages: 2
3Com 3C16710 - OfficeConnect 8/TPM Hub User Manual preview
3C16710 - OfficeConnect 8/TPM Hub
Brand: 3Com Pages: 130
Cabletron Systems MMAC-Plus 9T125-24 Supplementary Manual preview
MMAC-Plus 9T125-24
Brand: Cabletron Systems Pages: 36
DirectConnect 43136 User Manual preview
43136
Brand: DirectConnect Pages: 10
Phonocar 5-981 Mounting Instructions preview
5-981
Brand: Phonocar Pages: 2
Cabletron Systems 6H122-08 User Manual preview
6H122-08
Brand: Cabletron Systems Pages: 170
H3C S5120-EI Series Configuration Commands preview
S5120-EI Series
Brand: H3C Pages: 29
Black Box LE2650A Specifications preview
LE2650A
Brand: Black Box Pages: 2
Vigitron MaxiiNet VI3026 Operational Manual preview
MaxiiNet VI3026
Brand: Vigitron Pages: 288
Tripp Lite 0SU70032 Quick Manual preview
0SU70032
Brand: Tripp Lite Pages: 3
C&H Technologies M218 User Manual preview
M218
Brand: C&H Technologies Pages: 28
Xantech HDMI3X1 User Manual preview
HDMI3X1
Brand: Xantech Pages: 5
Xcellon SH10-10H Manual preview
SH10-10H
Brand: Xcellon Pages: 2
LEGRAND Wattstopper EOSW Series Manual preview
Wattstopper EOSW Series
Brand: LEGRAND Pages: 12

Brands by name

Popular brands

Load more brands