manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Configuring IP Addressing 

IP Configuration 

through the switch, configure the switch with an IP address and subnet mask 
compatible with your network. The following table lists the general features 
available with and without a network-compatible IP address configured. 

Table 8-1. 

Features Available With and Without IP Addressing on the Switch 

Features Available Without an IP Address 

Additional Features Available with an IP Address and 
Subnet Mask 

•   Direct-connect access to the CLI and the menu interface. 
•   Stacking Candidate or Stack Member 
•   DHCP or Bootp support for automatic IP address 

configuration, and DHCP support for automatic Timep 
server IP address configuration 

•   Spanning Tree Protocol 
•   Port settings and port trunking 
•   Console-based status and counters information for 

monitoring switch operation and diagnosing problems 
through the CLI or menu interface. 

•   VLANs and GVRP 
•   Serial downloads of operating system (OS) updates and 

configuration files (Xmodem) 

•  Link  test  
•   Port monitoring 
•   Password authentication 
•   Quality of Service 
•   Authorized IP manager 

•   Web browser interface access, with configuration, 

security, and diagnostic tools, plus the Alert Log for 
discovering problems detected in the switch along with 
suggested solutions 

•   SNMP network management access such as ProCurve 

Manager network configuration, monitoring, problem-
finding and reporting, analysis, and recommendations for 
changes to increase control and uptime 

•   , RADIUS, SSH, SSL, and 802.1X authentication 
•   Multinetting on VLANs 
•   Stacking Commander* 
•   Telnet access to the CLI or the menu interface 
•  IGMP  
•   Timep server configuration 
•   TFTP download of configurations and OS updates 
•   IP routing 
•  Ping  test  

*Although a Commander can operate without an IP address, doing so makes it unavailable for in-band access in an IP 
network. 

DHCP/Bootp Operation 

Overview.  

DHCP/Bootp is used to provide configuration data from a DHCP 

or Bootp server to the switch. This data can be the IP address, subnet mask, 
default gateway, Timep Server address, and TFTP server address. If a TFTP 
server address is provided, this allows the switch to TFTP a previously saved 
configuration file from the TFTP server to the switch. With either DHCP or 
Bootp, the servers must be configured prior to the switch being connected to 
the network. 

N o t e    

For information on configuring DHCP relay, including setting up a DHCP 
helper and DHCP Option 82 on the switch, refer to the relevant section in the 
IP routing chapter of the 

Advanced Traffic Management Guide

. 

8-12 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link DI-707 User Manual preview
DI-707
Brand: D-Link Pages: 36
KELCO E30 Installation & Programming Manual preview
E30
Brand: KELCO Pages: 41
IOGear MicroHub GUH274W3 (Portuguese) Manual Do Usuário preview
MicroHub GUH274W3
Brand: IOGear Pages: 1
netvox ZigBee Z815B User Manual preview
ZigBee Z815B
Brand: netvox Pages: 14
Sangamo RPTS Q550 Installation & User'S Instructions preview
RPTS Q550
Brand: Sangamo Pages: 2
NTI UNIMUX-nXm-UHD Installation And Operation Manual preview
UNIMUX-nXm-UHD
Brand: NTI Pages: 69
H-Tronic TS 1000 Instruction Manual preview
TS 1000
Brand: H-Tronic Pages: 15
A-Neuvideo ANI-8PDU-24V Instruction Manual preview
ANI-8PDU-24V
Brand: A-Neuvideo Pages: 12
Power Ethernet PE 200AV T1000 Quick Setup Manual preview
PE 200AV T1000
Brand: Power Ethernet Pages: 2
WilTec SKD-1 Operation Manual preview
SKD-1
Brand: WilTec Pages: 7
IPGARD SDPN-2D Manual preview
SDPN-2D
Brand: IPGARD Pages: 15
Blue Sea Systems 8689 Manual preview
8689
Brand: Blue Sea Systems Pages: 2
SMC Networks EZ HUB 10/100 5608DS User Manual preview
EZ HUB 10/100 5608DS
Brand: SMC Networks Pages: 2
BJ Live BJ-277 User Manual preview
BJ-277
Brand: BJ Live Pages: 2
ENSIM SENSORS DX-ELB 11 Operating Manual preview
DX-ELB 11
Brand: ENSIM SENSORS Pages: 15
Xantech 686-10 Installation Instructions preview
686-10
Brand: Xantech Pages: 5
SMC Networks ZSE3 Instruction Manual preview
ZSE3
Brand: SMC Networks Pages: 3
LevelOne GEL-1072 Brochure & Specs preview
GEL-1072
Brand: LevelOne Pages: 4

Brands by name

Popular brands

Load more brands