manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Troubleshooting 

Diagnostic Tools 

Ping and Link Tests 

The Ping test and the Link test are point-to-point tests between your switch 
and another IEEE 802.3-compliant device on your network. These tests can 
tell you whether the switch is communicating properly with another device. 

N o t e    

To respond to a Ping test or a Link test, the device you are trying to reach must 
be IEEE 802.3-compliant. 

Ping Test.  

This is a test of the path between the switch and another device 

on the same or another IP network that can respond to IP packets (ICMP Echo 
Requests). 

Link Test.  

This is a test of the connection between the switch and a desig­

nated network device on the same LAN (or VLAN, if configured). During the 
link test, IEEE 802.2 test packets are sent to the designated network device 
in the same VLAN or broadcast domain. The remote device must be able to 
respond with an 802.2 Test Response Packet. 

C-33 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Manhattan 160605 Quick Start Manual preview
160605
Brand: Manhattan Pages: 2
Belkin OmniView Secure F1DN102Uea Quick Installation Manual preview
OmniView Secure F1DN102Uea
Brand: Belkin Pages: 36
Edge-Core AS7726-32X Quick Start Manual preview
AS7726-32X
Brand: Edge-Core Pages: 9
F&G PM 3 FG Series Installation Instructions Manual preview
PM 3 FG Series
Brand: F&G Pages: 6
H3C LS-5500-28C-PWR-SI-OVS Installation Manual preview
LS-5500-28C-PWR-SI-OVS
Brand: H3C Pages: 86
Xunison Hub D60 5G Quick Start Manual preview
Hub D60 5G
Brand: Xunison Pages: 14
Cabletron Systems SmartStack STS16-20R Installation And User Manual preview
SmartStack STS16-20R
Brand: Cabletron Systems Pages: 258
SMC Networks SMC8606SX Specification Sheet preview
SMC8606SX
Brand: SMC Networks Pages: 2
ABM AstroBox User Manual preview
AstroBox
Brand: ABM Pages: 8
ANTAIRA LMX-2602G-SFP Series Hardware Manual preview
LMX-2602G-SFP Series
Brand: ANTAIRA Pages: 19
QTech QSW-4600 Series Hardware Installation And Reference Manual preview
QSW-4600 Series
Brand: QTech Pages: 58
Penguin Computing Arctica 1600cs Installation Manual preview
Arctica 1600cs
Brand: Penguin Computing Pages: 71
Gefen HDMI-341 User Manual preview
HDMI-341
Brand: Gefen Pages: 12
LEGRAND Chief Kontour KPWR Series Installation Instructions Manual preview
Chief Kontour KPWR Series
Brand: LEGRAND Pages: 8
CYP CMSI-48E Operation Manual preview
CMSI-48E
Brand: CYP Pages: 24
CityGrow Systems CG800 Series User Manual preview
CG800 Series
Brand: CityGrow Systems Pages: 21
Gefen EXT-UHD600-41 User Manual preview
EXT-UHD600-41
Brand: Gefen Pages: 136
Mengual Hera IR-S Assembly And Operating Instructions preview
Hera IR-S
Brand: Mengual Pages: 2

Brands by name

Popular brands

Load more brands