manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Configuring for Network Management Applications 

Using SNMP Tools To Manage the Switch 

[no] snmpv3 group group_name user user_name sec-model <ver1| ver2c 
| ver3> 

(— Continued —) 

user user_name 

This is the user to be added to the access group. This 
must match the user name added with the 

snmpv3 user 

command

. 

sec-model <ver1 | ver2c | ver3> 

This defines which security model to use for the added 
user.  A SNMPv3 access Group should only use the ver3 
security model. 

To establish a user you must first add the user names to the list of known 
users. Add user names with the 

snmpv3 user 

CLI command. 

Add user Network Admin with no 
Authentication or  Privacy 

Add user Network Mgr  with 
authentication and privacy 

Privacy is used and the 
password is set  privpass 

Authentication is set to Md5 
and the password is authpass 

Figure 13-2.  Adding and showing Users for SNMPv3 

13-9 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Barco Matrix-PRO HD-SDI Specifications preview
Matrix-PRO HD-SDI
Brand: Barco Pages: 2
FELA SWITCH CASAMBI Operation And Installation Manual preview
SWITCH CASAMBI
Brand: FELA Pages: 13
H3C s5820x series Quick Start Manual preview
s5820x series
Brand: H3C Pages: 32
H3C S5830V2 series Mce Command Reference preview
S5830V2 series
Brand: H3C Pages: 22
H3C s5820x series Command Reference Manual preview
s5820x series
Brand: H3C Pages: 488
H3C S10500X Series Installation, Quick Start preview
S10500X Series
Brand: H3C Pages: 3
H3C S7500 Series Manual preview
S7500 Series
Brand: H3C Pages: 8
H3C S7500 Series Command Manual preview
S7500 Series
Brand: H3C Pages: 25
H3C S12500 Series Manual preview
S12500 Series
Brand: H3C Pages: 31
H3C S12500 Series Interface Configuration Manual preview
S12500 Series
Brand: H3C Pages: 23
H3C S12500 Series Software Upgrade preview
S12500 Series
Brand: H3C Pages: 24
H3C S12500 Series Installation Instructions Manual preview
S12500 Series
Brand: H3C Pages: 126
H3C S12500-X Configuration Manual preview
S12500-X
Brand: H3C Pages: 42
H3C S6300 Series Troubleshooting Manual preview
S6300 Series
Brand: H3C Pages: 32
H3C S7500 Series Installation Manual preview
S7500 Series
Brand: H3C Pages: 13
H3C S12500 Series Reference preview
S12500 Series
Brand: H3C Pages: 16
H3C S12500 Series Configuration Manual preview
S12500 Series
Brand: H3C Pages: 39
Hama 78499 Operating Instructions Manual preview
78499
Brand: Hama Pages: 10

Brands by name

Popular brands

Load more brands