manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

MAC Address Management 

Determining MAC Addresses in the Switch 

■

  

Use the CLI

 to view the switch’s port MAC addresses in hexadecimal 

format. 

Menu: Viewing the Switch’s MAC Addresses 

The Management Address Information screen lists the MAC addresses for: 

■

  

Base switch (default VLAN; VID = 1) 

■

  

Any additional VLANs configured on the switch. 

Also, the Base MAC address appears on a label on the back of the switch. 

N o t e    

The Base MAC address is used by the first (default) VLAN in the switch. This 
is usually the VLAN named “DEFAULT_VLAN” unless the name has been 
changed (by using the VLAN Names screen). On the switches covered by this 
guide, the VID (VLAN identification number) for the default VLAN is always 
"1", 

and cannot be changed

. 

To View the MAC Address (and IP Address) assignments for VLANs 
Configured on the Switch:  

1.   From the Main Menu, Select 

1. Status and Counters 

2. Switch Management Address Information 

If the switch has only the default VLAN, the following screen appears. If 
the switch has multiple static VLANs, each is listed with its address data. 

Switch Base (or Default 
VLAN) MAC address 

Current IP Address 
Assigned to the Switch 

Figure D-1.Example of the Management Address Information Screen 

D-3 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link DKVM-IP1 Manual preview
DKVM-IP1
Brand: D-Link Pages: 73
3Com Switch 4500 Family Datasheet preview
Switch 4500 Family
Brand: 3Com Pages: 16
3Com PathBuilder S200 Series User Manual preview
PathBuilder S200 Series
Brand: 3Com Pages: 32
H3C s5820x series Quick Start Manual preview
s5820x series
Brand: H3C Pages: 32
H3C S5830V2 series Mce Command Reference preview
S5830V2 series
Brand: H3C Pages: 22
H3C s5820x series Command Reference Manual preview
s5820x series
Brand: H3C Pages: 488
H3C S10500X Series Installation, Quick Start preview
S10500X Series
Brand: H3C Pages: 3
H3C S7500 Series Manual preview
S7500 Series
Brand: H3C Pages: 8
H3C S7500 Series Command Manual preview
S7500 Series
Brand: H3C Pages: 25
H3C S12500 Series Manual preview
S12500 Series
Brand: H3C Pages: 31
H3C S12500 Series Interface Configuration Manual preview
S12500 Series
Brand: H3C Pages: 23
H3C S12500 Series Software Upgrade preview
S12500 Series
Brand: H3C Pages: 24
H3C S12500 Series Installation Instructions Manual preview
S12500 Series
Brand: H3C Pages: 126
H3C S12500-X Configuration Manual preview
S12500-X
Brand: H3C Pages: 42
H3C S6300 Series Troubleshooting Manual preview
S6300 Series
Brand: H3C Pages: 32
H3C S7500 Series Installation Manual preview
S7500 Series
Brand: H3C Pages: 13
H3C S12500 Series Reference preview
S12500 Series
Brand: H3C Pages: 16
H3C S12500 Series Configuration Manual preview
S12500 Series
Brand: H3C Pages: 39

Brands by name

Popular brands

Load more brands