manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Configuring for Network Management Applications 

LLDP (Link-Layer Discovery Protocol) 

N o t e    

Because ProCurve switches do not generate CDP packets, they are not 
represented in the CDP data collected by any neighbor devices running CDP. 

A switch with CDP disabled forwards the CDP packets it receives from other 
devices, but does not store the CDP information from these packets in its own 
MIB. 

LLDP data transmission/collection and CDP data collection are both enabled 
in the switch’s default configuration. In this state, an SNMP network 
management application designed to discover devices running either CDP or 
LLDP can retrieve neighbor information from the switch regardless of whether 
LLDP or CDP is used to collect the device-specific information. 

Protocol State  Packet 

Generation 

Inbound Data Management  Inbound Packet Forwarding 

CDP Enabled

1 

n/a 

Store inbound CDP data. 

No forwarding of inbound 
CDP packets. 

CDP Disabled 

n/a 

No storage of CDP data from  Floods inbound CDP packets 
neighbor devices. 

from connected devices to 
outbound ports. 

LLDP Enabled

1 

Generates and  Store inbound LLDP data. 

No forwarding of inbound 

transmits 

LLDP packets. 

LLDP packets 
out all ports on 
the switch. 

LLDP Disabled   No packet 

No storage of LLDP data 

No forwarding of inbound 

generation. 

from neighbor devices. 

LLDP packets. 

1

Both CDP data collection and LLDP transmit/receive are enabled in the default configuration. 

If a switch receives CDP packets and LLDP packets from the same neighbor device on the 
same port, it stores and displays the two types of information separately if the chassis and 
port ID information in the two types of advertisements is different.  In this case, if you want 
to use only one type of data from a neighbor sending both types, disable the unwanted 
protocol on either the neighbor device or on the switch. However, if the chassis and port ID 
information in the two types of advertisements is the same, the LLDP information overwrites 
the CDP data for the same neighbor device on the same port. 

13-55 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

OEM VX-100 Specifications preview
VX-100
Brand: OEM Pages: 1
Dahua DH-PFS3206-4P-120 User Manual preview
DH-PFS3206-4P-120
Brand: Dahua Pages: 19
Steren SHOME-140 User Manual preview
SHOME-140
Brand: Steren Pages: 13
DeLOCK 11481 User Manual preview
11481
Brand: DeLOCK Pages: 26
MicroNet SP1659P User Manual preview
SP1659P
Brand: MicroNet Pages: 123
Banner SI-HG63FQDR Instruction Manual preview
SI-HG63FQDR
Brand: Banner Pages: 8
MCOHome MH-S312 User Manual preview
MH-S312
Brand: MCOHome Pages: 3
Mellanox Technologies Grid Director 4700 Installation Manual preview
Grid Director 4700
Brand: Mellanox Technologies Pages: 88
Kramer WP-211X Quick Start Manual preview
WP-211X
Brand: Kramer Pages: 3
MaxTech FHX-1200 User Manual preview
FHX-1200
Brand: MaxTech Pages: 10
Knightsbridge IP663G Installation & Maintenance Manual preview
IP663G
Brand: Knightsbridge Pages: 8
MyCableMart SW31NN00N User Manual preview
SW31NN00N
Brand: MyCableMart Pages: 2
Panio CH8810K User Manual preview
CH8810K
Brand: Panio Pages: 12
Panduit Atlona AT-HDR-SW-52 Installation Manual preview
Atlona AT-HDR-SW-52
Brand: Panduit Pages: 12
KinAn KM0104 Manual preview
KM0104
Brand: KinAn Pages: 7
RGBLE S00203 User Manual preview
S00203
Brand: RGBLE Pages: 6
GarrettCom Magnum S14 Installation And User Manual preview
Magnum S14
Brand: GarrettCom Pages: 61
Dell Brocade DCX Configuration Manual preview
Brocade DCX
Brand: Dell Pages: 1436

Brands by name

Popular brands

Load more brands