HP ProCurve 2610-24 Management And Configuration Manual Download Page 412

Page: 412 / 464

Troubleshooting

Using Logging To Identify Problem Sources

(The event log is

not

erased by using the

Reboot Switch

command in the Main

Menu.)

Table C-1.Event Log System Modules

Module

Event Description

Module

Event Description

addrMgr

Address table

mgr

Console management

chassis

switch hardware

ports

Change in port status; static trunks

bootp

bootp addressing

snmp

SNMP communications

console

Console interface

stack

Stacking

dhcp

DHCP addressing

stp

Spanning Tree

download

file transfer

sys, system

Switch management

FFI

Find, Fix, and Inform -- available in the

telnet

Telnet activity

console event log and web browser
interface alert log

garp

GARP/GVRP

tcp

Transmission control

igmp

IP Multicast

tftp

File transfer for new OS or config.

IP-related

timep

Time protocol

ipx

Novell Netware

vlan

VLAN operations

lacp

Dynamic LACP trunks

Xmodem

Xmodem file transfer

C-22

Summary of Contents for ProCurve 2610-24
















































































































































































































































































































































































































































































Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands

HP ProCurve 2610-24, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands