HP ProCurve 2610-24 Management And Configuration Manual Download Page 365

Page: 365 / 464

Monitoring and Analyzing Switch Operation

Overview

The switch has several built-in tools for monitoring, analyzing, and trouble
shooting switch and network operation:

■

Status:

Includes options for displaying general switch information, man

agement address data, port status, port and trunk group statistics, MAC
addresses detected on each port or VLAN, and STP, IGMP, and VLAN data

(page B-4)

■

Counters:

Display details of traffic volume on individual ports

(page

B-10)

■

Event Log

: Lists switch operating events

(“Using Logging To Identify

Problem Sources” on page C-21)

■

Alert Log:

Lists network occurrences detected by the switch—in the

Status | Overview screen of the web browser interface

(page 5-6)

■

Configurable trap receivers:

Uses SNMP to enable management sta

tions on your network to receive SNMP traps from the switch (

“SNMP

Notification and Traps” on page 13-18

■

Port monitoring (mirroring):

Copy all traffic from the specified ports

to a designated monitoring port

(page B-23)

N o t e

Link test and ping test—analysis tools in troubleshooting situations—are
described in chapter 18, “Troubleshooting”. See page C-33.

B-3

Summary of Contents for ProCurve 2610-24
















































































































































































































































































































































































































































































Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands

HP ProCurve 2610-24, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands